The truck on the road, the driver to see the barometer and avoid the vehicle pressure too low and cause no brakes, large trucks turning to expand the turning radius, to take appropriate for the sharp angle, considering the difference in the round, but also used to see the mirror. Baotou North rush heavy truck parts, clutch do not often step on, do not semi linkage, this will cause clutch damage, when the vehicle does not need to step on the clutch, braking is good.

The big trucks hit about 3.5 laps around the direction, pulling too much in practice and not rubbing the dishes. In parking and reversing, should pay attention to consider the trajectory of large trucks and space locations. If you want to overtake, keep plenty of space and don't worry about steering the wheel. A large truck hundred Mega downshift driving also has the skill of the driver in the startup and gear in the normal route, the truck immediately trample the accelerator pedal, let the car rapidly than the stall a stall to engage in vulgar range in the clutch after raising gas when the engine and truck without shaking the fit. If the wobble, low speed to improve the speed that. Also, if large trucks appear recoil, this shows higher speed, should be less mention. The gear lever should be shifted high to one gear, and then speed up. In the downshift, it is found that there are obstacles, if the big truck near the road when uneven, the speed of the vehicle is still fast, this time the use of brakes to speed down to bump road when the vehicle does not appear big bumps so far.

The following several points, the slow speed, gear, brake less flexible, turning the steering wheel greatly, slightly larger sink, when driving, attention to light is the opposite position in the car steering lamp, the eyes to see the barometer and prevent the air pressure is too low to no brakes, turn attention to expand the turning radius the eyes, not only have to look at the front mirror, and then the clutch, the clutch often don't tread, not half clutch linkage, then that will wear, deceleration is not necessary to step on the clutch, only the brakes can be timely in a lot of ramp stalls to climb, downhill on the gap, pay attention to the stock brake oil…

Braking can not be continuous braking, pay attention to air pressure, to prevent loss of control. Because the air pressure braking reaction is quick, must practice more, grasps dynamics

Whether it is a few meters of the car as long as the method of single machine, after the wheel turning radius of the center, you can know how to play the steering wheel, such as 90 degree turn, let the inner corner by rear wheel close to the bending angles of the rear wheel, arrive when you can turn the steering wheel in the width allowed (death case next,) also want to pay attention to the surrounding environment.

If there is an obstacle in front of the gear, if the vehicle is approaching the concave convex Road, the speed will be faster. Then the brake can be used to reduce the vehicle speed to the bump road. In the further deceleration of the brake, if the vehicle is about to wobble, the clutch pedal is lowered and the speed is lowered to the lower end of the gear range. Speed change gear should keep in mind the principle of "gear up first, reduce gear first, slow down".

Before blocking, blow the throttle, lift the speed up first, and then take off the accelerator before the gear is cut to slow down the speed.

In the shift, as the "two from legitimate", added a block according to "step (clutch), pick (neutral), step (clutch), hanging (speed)" principle, fast stomp on the clutch pedal, can easily increase the gear.

The reduction gear, according to the "tread (clutch), pick (neutral), lift (clutch), detonation (throttle), foot (clutch), hanging (low gear)" principle, stomp on the clutch, and the oil in the detonation of a foot air foot clutch, and keep for a moment, and then stepped down second the foot clutch pedal, at the same time the Baotou beiben heavy truck parts is transformed into low gear shift lever. Uphill gear

The car in the uphill block, due to the increase of the uphill drag, so to add flushing cars than in the road longer, Baotou beiben heavy truck engine power output more accessories. At the same time, after the car is washed, it is necessary to do a clutch pedal, cutting the power and sudden oil synchronization action. At this time, the car on the slope dynamic decay quickly, which requires the driver in the uphill and stop before, must fully wash the car, easy to set aside for beginners delays due to slow time, so as to avoid the lack of power drag block add block. In short, the emphasis on uphill is to avoid the shortage of cars.